- Can you run waste pipe through joists?
- Can you run electrical wire through ceiling joists?
- How big a hole can you drill in a floor joist?
- Can you put plumbing through floor joists?
- Can soil pipe go under floorboards?
- How do you strengthen a notched joist?
- Where do I drill holes in I joist?
- Can PEX be run through floor joists?
- Can you cut into floor joists?
- Can you run two wires through the same hole?
- Can you run electrical wire under house?
Can you run waste pipe through joists?
You need (from memory) a fall of a minimum of 18mm per metre run on the pipe.
To get that fall, not all your holes will be in the centre of a joist, although they won’t be far off.
You’d have to work it out..
Can you run electrical wire through ceiling joists?
Running electrical wire through the channel between ceiling joists is generally easiest. In addition, your light fixture may require mounting to a ceiling joist or to two short blocks nailed between the joists. Trace and mark the fixture hole and cut out with a drywall saw, utility knife or reciprocating saw.
How big a hole can you drill in a floor joist?
The hole cannot be larger than one-third the depth of the joist, so the maximum hole size for a 2×12 joist (actual size 1-1/2 x 11-1/4 in.) is 3-3/4 in. diameter—plenty big enough for running cable! You can drill the holes anywhere along the length of the joist (first photo).
Can you put plumbing through floor joists?
The maximum allowable diameter of a hole in any solid-lumber joist is one-third of the joist’s depth. Notches can’t be deeper than one-sixth of the joist depth. … Although notches aren’t allowed in the center third of a joist’s length, you can drill holes anywhere along the length of the floor joist in that 5 1⁄4-in.
Can soil pipe go under floorboards?
Soil pipes are generally located on an outside wall and enter the bathroom as close as possible to the toilet location. They can be mounted on the floor, but usually pipes run below the floor in-between the floor joists. … Running this pipe from one end of the house to the other simply is not practical.
How do you strengthen a notched joist?
You can reinforce a notched joist that has not cracked by cutting two pieces of 3/4-inch plywood as wide as the joist depth and as long as the plywood sheet. Screwing a piece to the joist on each side offers moderate reinforcement. Stronger reinforcement is in order if the joist is sagging or has cracked.
Where do I drill holes in I joist?
One notch may be cut anywhere except the middle of the length of the stud or column. Holes may be drilled anywhere along the length of the stud or column but must be at least 5″ from the edge.
Can PEX be run through floor joists?
Protect Your Pex Pipes that are encased in concrete (for in-floor heating, for example) are OK because the concrete holds them in place. And pipes running straight through wood studs and joists are fine too—just protect the pipe in areas where it bends as it passes through.
Can you cut into floor joists?
A: Floor joists occasionally need to be notched or drilled during construction, but you should take pre cautions not to weaken the structural strength of the framing member. … You can cut a notch at the end of the joist to 1/4 of the joist’s depth (maximum).
Can you run two wires through the same hole?
When pulling multiple wires through one hole be very carfull not to cause a friction burn on the other wires in the hole. Regardless of whether it is Code or not, you should only feed one wire through one hole. Drill a separate run of 3/4″ holes for each wire your run, even if they run parallel to each other.
Can you run electrical wire under house?
You can run the NM through the crawl space as long as you run it on the side of the framing, through bored holes, or on running boards. What the US National Electric Code does not permit is to run it across the bottom of the framing unless it is quite large or protected. Be carful running unarmoured cable.